MAGNUM Standard Freestyle Wheels (Indoor)
MAGNUM Standard Freestyle Wheels (Indoor)
MAGNUM 49D, 53D, 57D, and 60D – 57mm Standard FreeStyle Wheels
Part Number: STRUMAG 49, STRUMAG 53, STRUMAG 57, and STRUMAG 60
Hardness: Gray 49D, Cream 53D, Yellow 57D, and White 60D
Compound: MonoCompound Elastomeric ThermoPlastiche Formula
Normally available from our Skates US Stock: All Hardnesses
The Giotto 49D, 53D, 57D, and 60D Standard FreeStyle Wheels provide a great range of Grip and Roll for the Standard Series of FreeStyle Wheels. The Magnum is less expensive (than the Giotto and Urethane counterparts), yet, very high quality wheel, which is used on many types of skating surfaces including standard wood floors coated with plastic or poly urethane, but also unusual surfaces like, tile type basketball and volleyball courts, tennis courts (Indoor or outdoor), and concrete or terrazzo surfaces that are more common around the World. The Magnum FreeStyle Wheels are used a great deal internationally, where there are few indoor skating centers like there are here in the USA. The Magnum FreeStyle wheels are most often used on abusive surfaces where the life expectancy of the wheels on these tough surfaces are not very long, but very High Skating Quality both Grip and Roll are required. Many of the world level FreeStyle competitors use combinations of hardnesses of the Magnum for Training to achieve the best Skating result. Roll-Line has developed this wheel giving it properties that withstand the extreme and unusual abuse a FreeStyle skater and an abusive Skating Surface can dish out. The Roll-Line Magnum FreeStyle Wheels (49D, 53D, 57D, and 60D) are a Medium-Profile, durable wheel which are Strong, Light, and with extremely Close Tolerances for Roundness, Trueness, and for the Cage where the Bearings and Spacers are mounted. The Roll-Line Magnum FreeStyle Wheels are a MonoCompound Elastomeric ThermoPlastiche wheel, which is produced utilizing an injection system. The 49D, 53D, 57D, and 60D provide a great varying range of grip in the wheel material and is for a skating surfaces with a range of grip. The wheel color identifies which hardness the wheel is.
The softer the wheel, or lower Shore “D” hardness number, the more the grip and slightly less roll. The harder the wheel, or higher Shore “D” number, the more the roll, with slightly less grip.
It is almost always recommended to use spacers in the wheels, when using standard 7mm bearings. Long ago, before the use of Lock Nuts (the nuts that have the Nylon Plastic inserts) to hold the wheels on the axles, Jam Nuts were used, but when the spacer was not as wide as the web of the wheel, or the wheel was not machined accurately, the bearings would lock up, the nut had to be tight, and could not be “backed-off”. This method, of locking the Axle Nut down, did promote proper bearing alignment and did increase the diameter of the axle from 7mm to approximately 14mm, because everything was locked down, which also saved the problems of bent axles. Today we do use Lock Nuts. It is still very advisable to lock everything down (especially for FreeStyle, Jam, and Roller Derby Skaters). Roll-Line does provide Spacers for Roll-Line Wheels with each pair of Frames or they can be purchased separately. Properly locking the Wheels down when using standard bearing types, will also promote longer bearing life.
The Roll-Line 7mm SpeedRace & SpeedMax Bearings , are specifically made for very High Level Competitive FreeStyle Roller Skating and are a very Durable Bearing with lots of ROLL. The SpeedRace & SpeedMax Bearings are Free Rolling with minimal Radial Play which promotes and very evenly distributes the load across the 7 or 8 (of the SpeedMax) balls for optimal Roll and a good amount of Axial Play or Thrust, which is the side movement of the inner race in relation to the outer race. This movement is very important because when Skaters push, we always put side load on the skate to get power in the push or stroke. If the Bearing does not allow for this, it will bind and LOOSE operating speed or ROLL. These provisions in the Race Curvature and Contact Angle allow the Roll-Line SpeedRace & SpeedMax Bearings to ROLL very freely
The Roll-Line SpeedRace Bearings have 7 balls and a rubber sealant Shield and the SpeedMax have 8 balls and a metal Shield and are ONLY available for 7mm Axles. The Roll-Line SpeedRace & SpeedMax Bearings are skated on by most of the World level FreeStyle Skaters and Champions.